Introduction to Double Shaft Blender

Flat mouth mixer belongs to forward mixing and reverse feeding. Stirring plastic deformation and air drying forced concrete. This machine has the advantages of stable operation, convenient practical operation, high cost-effectiveness in mixing, and high production efficiency. When matched with feeding weighing equipment, it can form a small and medium-sized concrete mixing plant. Applicable to general construction projects, road surfaces, highway bridges, hydropower engineering, and other engineering projects.

The column type flat mouth mixer is a new type of concrete mixer suitable for general highways, power plants, embankment projects, construction, road surfaces, highway bridges, hydropower projects, and large, medium, and small cement plants. It has the advantages of stable operation, low energy consumption, compact structure, reliable transmission system, lightweight key, and high productivity. It can mix plastic deformation, dry forced, flowable concrete, light stone materials, and cement mortar.

Characteristics of Pingkou Garden Plate Blender:

The overall design concept of the equipment is effective and the performance is optimized;

2. Convenient application maintenance;

3. Sturdy and reliable, with a long lifespan;

4. High cost-effectiveness and efficiency in mixing

5. Convenient practical operation and faster material pouring speed

6. Low energy consumption and low noise

Maintenance of Pingkou Garden Plate Blender:

1. Ensure the cleanliness of the column type flat mouth mixer and its surrounding environment.

2. Immediately eliminate the material running in the silo and return the controller to zero normally.

3. Check if the lubricating grease at each lubrication point is sufficient, and ensure that the pneumatic three-way components in the gas supply system software have sufficient remaining oil.

4. Check if there are any overheating conditions or abnormal noises in the electric motors and household appliances, whether the dashboard markings are normal, and whether the signal system is intact.

5. Regularly inspect and adjust cylinders, disc valves, and solenoid valves to ensure that they open and close in accordance with regulations.

6. Regularly check the software of each system, and handle any issues such as ash leakage, steam leakage, oil leakage, and power failure properly.

7. The mixer and discharge bin should be cleaned every four hours to prevent residual concrete and soil from hindering normal operation.

8. Each class should drain the internal water stored in the air compressor, gas storage tank, and filtration device, and remove common malfunctions that occur during operation.

9. Disc valves, mixers, solenoid valves, air filters, and pneumatic triplets should be repaired and maintained according to the relevant instructions.

Product Introduction:

A dry powder mortar mixer, also known as a dry powder mortar mixer, is a mechanical device that uses mechanical equipment force and action to evenly mix two or more types of powder equipment materials. A dry mortar mixer can mix a variety of materials together to form a symmetrical compound; Can increase the contact area of materials to promote chemical changes; It can also accelerate the change of physical state, such as adding organic solvents to the concentration of granular substances, which can accelerate the melting and stirring according to the effectiveness of the mixing machinery.

Characteristic features:

The production and manufacturing of dry powder cement mortar, dry powder materials, and dry powder adhesives with different characteristics can be considered for the equipment of the dry powder mortar mixer, such as interior wall putty powder, dry powder building coatings, masonry building coatings, plastering mortar, cement mortar required for insulation systems, decorative design cement mortar, and various other dry powder cement mortars; And it has many advantages such as small footprint, low project investment, good results, and easy practical operation.

As a new type of professional powder mixing equipment, the dry powder mortar mixer has already received considerable five-star praise in the sales market, especially after the improvement of the basic principle of the machine equipment from column mixing to vertical mixing, the steadily increasing production rate has enabled this machine equipment to enter the hands of more customers. At present, the popular vertical dry powder mortar mixer in the sales market has the following characteristics:

1. The mixing speed is faster, and double-layer screw belts are used for mixing. The overall fitness of the material is faster, the production volume is high, and the average mixing time is 5-10 minutes;

2. One machine for use, it can also produce and manufacture inorganic insulation mortar, putty paste, plastering gypsum, exterior wall coatings, etc

3. The maintenance rate is low, and the rolling bearings are located on both sides of the mixer, making it difficult for materials to enter. The equipment is equipped with a cycloidal pin reducer, resulting in a low maintenance rate.

4. High mixing precision, all-round fitness and sports of materials, double-layer spiral belt, no dead corners in mixing, high precision, high cost-effectiveness;

5. Small footprint, fully automatic feeding equipment, improving work efficiency.

6. Circular cylinder structure, stable operation, low noise, long service life, and wide application fields.

Principle:

The mixer of the vertical spiral belt dry powder mortar mixer is designed with three layers of spiral gears inside and outside. During the operation of the mixer, the inner and outer spiral types push the material of the cylinder body to roll, and the inner spiral type pushes the material near the pivot to rotate, turning from inside to both sides to promote, and the material is directed towards the material layer; The outer spiral pushes the material layer to pivot, promoting it radially from both sides to the inside. The material is directed towards the interior and gathered, causing the spiral stirrer to roll the material over a large area of the cylinder body. The material is circulated in the thermal convection system of the cylinder body, cutting and infiltrating, and quickly and evenly mixed in a short period of time.

Nowadays, the country attaches great importance to green development. Green mountains and clear waters refer to people's concept of green development. Companies can no longer rely on extensive production management like before, but must adopt a refined management approach, which is very important for the industry.

The industry is a high energy consumption and high energy consumption manufacturing industry. In today's era where the country advocates green development, if the economic development mode cannot be changed, it will soon be gradually eliminated. The dry powder ball pressing machine manufactured by Huazhikai Equipment has further improved the efficiency of production and manufacturing, reduced air pollution, and increased economic benefits. So how did Huazhi Kai improve the ball press machine? During the entire process of the smelting plant, the slag powder is suppressed and shaped by a dry powder ball press, which can improve the high efficiency of the smelting plant, suppress the raw coal powder into balls, enhance the high efficiency of the raw coal, and reduce the air pollution caused by smoke and dust, which is conducive to transportation. Ball press machines have been widely used in manufacturing industries such as metallurgy, chemical plants, and decorative building materials. We warmly welcome new and old customers to visit and inspect our factory.